mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)
  • mDrawbot Kit (Standard Version)

mDrawbot Kit (Standard Version)

US $229.99

SKU: 90070 Weight: 3800.00 Gram
QTY: 0

Product Description

    

What is mDrawBot?

mDrawBot is the world's most fully-featured four-in-one drawing robot. It can be assembled into 4 different configurations: mScara, mSpider, mEggBot, and mCar.

A varity of components

This kit consists of over 60 components from Makeblock, including beams, brackets, motor, etc. It also comes with a specially-designed software named mDraw to control these robots. Here's the picture of all the components.

  
    

mScara

mScara is a SCARA (Selective Compliance Articulated Robot Arm) driven by stepper motors. Adding a pen on mScara, it can draw pictures on a flat surface. You can also turn mScara into a desktop laser engraver replacing the pen with a laser diode.

mSpider

mSpider is a drawing robot which can draw pictures on a wall or a white board. Two stepper motors control the movement of mSpider though strings. Theoretically, its drawing range can be expanded by increasing the length of the strings.

  
    

mEggBot

mEggBot is designed to draw on things that are improbable to print on, such as eggs or ping-pong balls. It can be used to write letters, draw expressions on spheroid, or draw Easter eggs.

mCar

mCar is a three-wheel robot car, which contains two stepper-motor-drive wheels and a ball-caster wheel. It can draw its own movement tracks on flat surface. Installing a chalk instead of a pen, it can draw on the floor.

  
    

Software

mDraw is the software specially designed for mDrawBot. After installing the mDraw software, you can import images that you wish your robot to draw. It is completely compatible with the four forms of mDrawBot and also both the servo mode and laser mode of Makeblock XY Plotter V2.0.

A Drawbot, and More than A Drawbot

This kit consists of over 60 components from Makeblock, including beams, brackets, motor, etc. It also comes with a specially-designed software named mDraw to control these robots. Here's the picture of all the components.Here are some examples of what you can do:

  
  

 

mDrawBot Animation Assembly

 

mScara

  

mSpider

mEggbot

  

mCar

 

WARNING:

Due to the particularity of laser, the application scope of the laser pack and products that included laser module is limited, please do not expand their application scope. Limitations are as follows:

1. The laser pack can only be used in the following kit:

• Use in mScara, one building form of mDrawbot (SKU: 90082, 90086)

• Use in XY Plotter Robot Kit (With Electronic Modules) (SKU: 90014)

(Note: For kits that included laser pack, we provide detailed manual and technical support.)

2. The laser pack can only be used in the following DIY product:

• DIY XY Plotter Robot Kit (Without Electronic Modules) (SKU: 91018)

• Other DIY products for personal use or agency use, for instance, transforming XY plotter or 3D Printer.

(Note: For using laser pack in DIY products, we only provide laser specification.)

About laser engraver pack (500mW)

WARNING: As laser energy has higher density, make sure corresponding protection measures are taken while using.

                1) No direct eye-contact with the laser light path;

                2) DO NOT irradiate others by the laser;

                3) Keep it away from children and other people who are not familiar with laser usage.

Specifications (mDrawBot)
1. Frame: Anodized Aluminum
  mScara mSpider mEggBot mCar
Working Area (mm2) 120° of an annulus (exradius 208mm, inradius 168mm) / Cylinder with L×D=60×(10-60) /
2. Power Supply:
  Voltage Current Frequency  
Input AC 100-240V 0.6A 50-60 Hz  
Output DC 12V 2.0 A /  
3. Main Controller: Makeblock Orion (Arduino UNO compatible)
4. Software: mDraw
5. Connection: USB or Bluetooth
6. Supported File Types: .Plain SVG, .BMP etc.
7. Supported OS: Windows7 or later. (Will be available in Mac OS X, Linux soon.)
8. Package Contains:

• Aluminum Extrusion Parts

• Plastic Timing Pulley 90T

• Timing Pulley 18T

• Pen Lift Mechanism

• Makeblock Orion(Controller)

• Stepper Motors

• Stepper Motor Drivers

• 9g Micro Servo Pack

• Cables

• Other Hardware and Accessories


Specifications (Laser Engraver)
Laser Engraver Pack (500mW) Remark
Wavelength 405nm  
Power 500mW  
W/ Voltage Conversion Box Input DC 12V 1.5A +
W/O Voltage Conversion Box Input DC 5V±0.2V 200mA -
Operating Temperature 0℃-50℃  
Storage & Transport temperature -40℃-85℃  
Processable Material
Material Cut Engraver
Paper YES YES
Cardboard up to 1.5mm YES
Wood Board up to 1.5mm YES
Rubber Sheet up to 0.5mm YES
Foam Paper up to 2.5mm YES
Dark color cloth (jean cloth, cotton cloth and linen) up to 0.5mm YES
Non-transparent ACRYL Up to 0.5mm (※1) YES
Plastic Sheet Up to 0.25mm (※2) YES
Urethane Sheet up to 2mm up YES
Mirror NO NO
Glass NO NO
Ceramic NO NO
Aluminum NO YES (※ 3)
Steel NO NO
Stainless NO NO

※1. Opaque black acrylic only, ※ 2.Gray plastic plate only, ※ 3.Peeling of anodized only.

Version: Standard (SKU: 90070)
1 x Beam 0824-032 1 x Threaded Shaft 4x39mm 50 x Nut M4
2 x Beam 0824-096 1 x Circle Shaft D4x80mm 4 x Nylon Stud M4x30
3 x Beam 0324-184 2 x Shaft Collar 4mm 2 x Plastic Ring 4x8x1mm
3 x Bracket 3x3 5 x Flange Bearing 4x8x3mm 8 x Plastic Ring 4x7x3mm
3 x Plate 3x6 1 x Square Nut M4 4 x Plastic Ring 4x7x10mm
1 x Bracket U1 3 x Nylon Cap Nut M4 2 x Plastic Rivet R4060
4 x Timing Pulley Slice 90T 1 x Polyester Thread(8m) 4 x Plastic Rivet R40120
2 x 42BYG Stepper Motor Bracket 2 x Timing Belt 112MXL 1 x 9g Micro Servo Pack
2 x Plastic Timing Pulley 90T 10 x Nylon Cable Tie 2 x100 2 x 42BYG Stepper Motor
2 x Tire 90T B 1 x Rubber Bank 2 x Base Bracket
1 x Caster Wheel 1 x Cross&2.5mm HEX Screwdriver 1 x Battery Holder
2 x Rubber Blanket 1 x HEX Key 1.5mm 1 x Makeblock Orion
2 x Shaft Connector 4mm 1 x Wrench 5mm&7mm 2 x Me Stepper Motor Driver
2 x Timing Pulley 18T 26 x Screw M4x8 1 x RJ25 Adapter
1 x Pen Holder and V Clamp 42 x Screw M4x16 1 x AC/DC Adapter 12V/2A
2 x 2 Inch G Clamp 5 x Screw M4x22 1 x 9g Servo Extension Cord
1x Plastic Hinge 1 x Screw M4x35 2 x 6P6C RJ25 Cable-20cm
1 x Plastic Hinge Gasket 6 x Headless Set Screw M3x5 1 x 6P6C RJ25 Cable-35cm
1 x Spring 0.6x6x50 8 x Countersunk Screw M3x8 1 x Micro USB Cable
1×tape 100cm(Paper)    
Version: Bluetooth (SKU: 90078)
1 x Beam 0824-032 1 x Threaded Shaft 4x39mm 50 x Nut M4
2 x Beam 0824-096 1 x Circle Shaft D4x80mm 4 x Nylon Stud M4x30
3 x Beam 0324-184 2 x Shaft Collar 4mm 2 x Plastic Ring 4x8x1mm
3 x Bracket 3x3 5 x Flange Bearing 4x8x3mm 8 x Plastic Ring 4x7x3mm
3 x Plate 3x6 1 x Square Nut M4 4 x Plastic Ring 4x7x10mm
1 x Bracket U1 3 x Nylon Cap Nut M4 2 x Plastic Rivet R4060
4 x Timing Pulley Slice 90T 1 x Polyester Thread(8m) 4 x Plastic Rivet R40120
2 x 42BYG Stepper Motor Bracket 2 x Timing Belt 112MXL 1 x 9g Micro Servo Pack
2 x Plastic Timing Pulley 90T 10 x Nylon Cable Tie 2 x100 2 x 42BYG Stepper Motor
2 x Tire 90T B 1 x Rubber Bank 2 x Base Bracket
1 x Caster Wheel 1 x Cross&2.5mm HEX Screwdriver 1 x Battery Holder
2 x Rubber Blanket 1 x HEX Key 1.5mm 1 x Makeblock Orion
2 x Shaft Connector 4mm 1 x Wrench 5mm&7mm 2 x Me Stepper Motor Driver
2 x Timing Pulley 18T 26 x Screw M4x8 1 x RJ25 Adapter
1 x Pen Holder and V Clamp 42 x Screw M4x16 1 x AC/DC Adapter 12V/2A
2 x 2 Inch G Clamp 5 x Screw M4x22 1 x 9g Servo Extension Cord
1 x Plastic Hinge 1 x Screw M4x35 2 x 6P6C RJ25 Cable-20cm
1 x Plastic Hinge Gasket 6 x Headless Set Screw M3x5 1 x 6P6C RJ25 Cable-35cm
1 x Spring 0.6x6x50 8 x Countersunk Screw M3x8 1 x Micro USB Cable
1 x Me-Bluetooth 4.0 1×tape 100cm(Paper)  
Version: Laser (SKU: 90082)
1 x Beam 0824-032 1 x Threaded Shaft 4x39mm 50 x Nut M4
2 x Beam 0824-096 1 x Circle Shaft D4x80mm 4 x Nylon Stud M4x30
3 x Beam 0324-184 2 x Shaft Collar 4mm 2 x Plastic Ring 4x8x1mm
3 x Bracket 3x3 5 x Flange Bearing 4x8x3mm 8 x Plastic Ring 4x7x3mm
3 x Plate 3x6 1 x Square Nut M4 4 x Plastic Ring 4x7x10mm
1 x Bracket U1 3 x Nylon Cap Nut M4 2 x Plastic Rivet R4060
4 x Timing Pulley Slice 90T 1 x Polyester Thread(8m) 4 x Plastic Rivet R40120
2 x 42BYG Stepper Motor Bracket 2 x Timing Belt 112MXL 1 x 9g Micro Servo Pack
2 x Plastic Timing Pulley 90T 10 x Nylon Cable Tie 2 x100 2 x 42BYG Stepper Motor
2 x Tire 90T B 1 x Rubber Bank 2 x Base Bracket
1 x Caster Wheel 1 x Cross&2.5mm HEX Screwdriver 1 x Battery Holder
2 x Rubber Blanket 1 x HEX Key 1.5mm 1 x Makeblock Orion
2 x Shaft Connector 4mm 1 x Wrench 5mm&7mm 2 x Me Stepper Motor Driver
2 x Timing Pulley 18T 26 x Screw M4x8 1 x RJ25 Adapter
1 x Pen Holder and V Clamp 42 x Screw M4x16 1 x AC/DC Adapter 12V/2A
2 x 2 Inch G Clamp 5 x Screw M4x22 1 x 9g Servo Extension Cord
1 x Plastic Hinge 1 x Screw M4x35 2 x 6P6C RJ25 Cable-20cm
1 x Plastic Hinge Gasket 6 x Headless Set Screw M3x5 1 x 6P6C RJ25 Cable-35cm
1 x Spring 0.6x6x50 8 x Countersunk Screw M3x8 1 x Micro USB Cable
1 x Laser Engraver Upgrade Pack(500mW) 1×tape 100cm(Paper)  
Version: Laser+Bluetooth (SKU: 90086)
1 x Beam 0824-032 1 x Threaded Shaft 4x39mm 50 x Nut M4
2 x Beam 0824-096 1 x Circle Shaft D4x80mm 4 x Nylon Stud M4x30
3 x Beam 0324-184 2 x Shaft Collar 4mm 2 x Plastic Ring 4x8x1mm
3 x Bracket 3x3 5 x Flange Bearing 4x8x3mm 8 x Plastic Ring 4x7x3mm
3 x Plate 3x6 1 x Square Nut M4 4 x Plastic Ring 4x7x10mm
1 x Bracket U1 3 x Nylon Cap Nut M4 2 x Plastic Rivet R4060
4 x Timing Pulley Slice 90T 1 x Polyester Thread(8m) 4 x Plastic Rivet R40120
2 x 42BYG Stepper Motor Bracket 2 x Timing Belt 112MXL 1 x 9g Micro Servo Pack
2 x Plastic Timing Pulley 90T 10 x Nylon Cable Tie 2 x100 2 x 42BYG Stepper Motor
2 x Tire 90T B 1 x Rubber Bank 2 x Base Bracket
1 x Caster Wheel 1 x Cross&2.5mm HEX Screwdriver 1 x Battery Holder
2 x Rubber Blanket 1 x HEX Key 1.5mm 1 x Makeblock Orion
2 x Shaft Connector 4mm 1 x Wrench 5mm&7mm 2 x Me Stepper Motor Driver
2 x Timing Pulley 18T 26 x Screw M4x8 1 x RJ25 Adapter
1 x Pen Holder and V Clamp 42 x Screw M4x16 1 x AC/DC Adapter 12V/2A
2 x 2 Inch G Clamp 5 x Screw M4x22 1 x 9g Servo Extension Cord
1 x Plastic Hinge 1 x Screw M4x35 2 x 6P6C RJ25 Cable-20cm
1 x Plastic Hinge Gasket 6 x Headless Set Screw M3x5 1 x 6P6C RJ25 Cable-35cm
1 x Spring 0.6x6x50 8 x Countersunk Screw M3x8 1 x Micro USB Cable
1 x Laser Engraver Upgrade Pack(500mW) 1 x Me-Bluetooth 4.0 1×tape 100cm(Paper)

 aio.gif

 

All-in-One Package

This package has everything you need to play with mDrawBot.

mDrawBot Download Package - Mac Version (515.81 MB)

mDrawBot Download Package - Windows Version (448.13 MB)

Package includes:

Brief Introduction - V1.0 PDF (794.07 KB)
mDrawBot User Guide (78.63 MB)
Assemble Instruction V1.1 PDF (23.13 MB)
FAQ (6.95 MB)
mDraw Software (Windows Version/ Mac Version) (29.65MB)
Software Instruction (mDraw inkscape & CorelDRAW) (5.36 MB)
Example SVG Files (4.72 MB)
Software Package (92.67 MB)

 brief-introduction.gif  

Brief Introduction - V1.0 PDF (794.07 KB)

This will give you a brief introduction for mDrawBot.

Click the picture on the left side to download it.

 user-guide.gif

  

mDrawBot User Guide (78.63 MB)

Click the picture on the left side to download it.

 assemble-instruction.gif

  

Assemble Instruction V1.1 PDF (23.13 MB)

This instruction will show you how to build the 4 forms of mDrawBot.

Click the picture on the left side to download it.

 faq.gif

  

FAQ (6.95 MB)

Click the picture on the left side to download it.

 software-mac.gif

  

mDraw Software (Mac Version) (29.65MB)

Click the picture on the left side to download it.

 software-win.gif

  

mDraw Software (Windows Version) (22.77 MB)

Click the picture on the left side to download it.

 software-instruction.gif

  

Software Instruction (mDraw inkscape & CorelDRAW) (5.36 MB)

Click the picture on the left side to download it.

 svg.gif

  

Example SVG Files (4.72 MB)

This pack include several SVG picture files for you to use in mDraw.

Click the picture on the left side to download it.

 software-pack.gif

  

Software Package (92.67 MB)

This pack include several BMP and SVG picture files for you to use in mDraw.

Click the picture on the left side to download it.

  • .Payment

    Payment can be made by either PayPal or Bank Transfer, whichever customers would like to use.

    PayPal

    The advantage of using PayPal is the timeliness, while the disadvantage is the relatively high commission fee charged by PayPal. Therefore, PayPal is usually recommended for order of small amount.

    Bank Transfer

    In terms of Bank Transfer, it will take longer time, even one week to the maximum; however, the handling charge is lower to some extent; so, Bank Transfer is preferred when the order value is large.

  • .Shipping Policy

    Free shipping

    For any orders with value exceeding USD 300, free shipping will be provided (excluding 3D printer and MakerSpace Kits); however, free shipping is not available for orders subject to discounts.

    PS: the customer for which free shipping is provided may not designate the courier, which will be determined at the sole discretion of Makeblcok.

    Delivery

    Delivery will be made within 1-2 working days after the receipt of payment. Since the commodities will be shipped through forwarder, the tracking number may sometimes be updated on the third working day. After we get to know the tracking number, we will update on our website and at the same time, the customer will be reminded via mail. Otherwise, customers can log onto "my account" to view the order status via "view order status".

    Tariff

    Makeblock abides by applicable laws and policies and will make declaration on true condition.

    All Makeblock commodities are exported through Hong Kong (free trade port); therefore, customers are not required to pay any export tariff. When commodities arrive at the destination, some will be checked by the customs and certain tariff shall be paid or not, depending on the provisions and operations of each country. Since all the import tariffs depend on local policies, customers are required to undertake related expenses at the destination port, if any.

    If you have any doubts about local tariff policies and potential tariffs, please refer to http://www.dutycalculator.com/new-import-duty-and-tax-calculation/saved_calculations/view_details/194962255/. Note: the information stated on the website is only provided for reference and Makeblock will not be liable for the final tariff and estimated tariff.

    Delivery range

    Basically, Makeblock will provide express services where the courier services are available. If you have any related questions, please feel free to contact us via ntec-support@makeblock.cc.

    Address

    For international express, PO BOX is not allowed; please indicate complete address (other than PO BOX), including domicile, postal code, addressee and contact information.

  • .After-Sale Support

    Technical question

    For any questions about the use of products, please view the related FAQ or seek relevant solutions at our forum http://forum.makeblock.cc/. Many customers that may have the same questions with you may have raised such questions and have been answered at the forum. Meanwhile, if you need relevant product information, please search at http://learn.makeblock.cc/. We have stored the information on all products here and classify them by products. If you are unable to find a solution at the above forum and learn, please send an email to tec-support@makeblock.cc, professional technical customer service personnel will answer your questions within 2 working days.

    Non-technical question

    If you have any questions about the order or product quality, please send an email to ntec-support@makeblock.cc, we will deal with your questions within 2 working days.

    Share

    Makeblock encourage and appreciate your share of your great ideas and creations with us and other people who love creation as you.

  • .Quality Assurance

    Returns and replacement for non-quality issues

    Time effectiveness& conditions: The commodityisunopened within 7 days from the date of receiptand can be resold.

    Procedure:

    1). Send an email with subject indicating "Applications for Returns and Replacement" to ntec-support@makeblock.cc.At the same time, the mail shall specify:

    a. Where the commodity was purchased (makeblcok official website /Amazon outlets /Taobao outlets/Jingdong outlets);

    b. Order No.;

    c. Tracking No..

    2). Within 2 working days after receiving the e-mail, Makeblock will verify and give a proposal for solving problem according to the actual condition.

    3). For the commodity needs to be returned, the customer, after well-packaging the same and filling in corresponding information, shall send the commodity to the location designated by Makeblock; and meanwhile, notify Makeblock of the tracking number by mail.

    4). After confirming that the commodity received complies with the returns and replacement conditions, Makeblock will refund within three working days.

    Expenses: Regarding the applications for returns and replacement for non-quality issues, all the freight and related costs, including but not limited to tariffs, shall beundertaken by the customer. (Note: Payment upon arrival is not allowed.)

    Refund: Corresponding refund will be returned to the account through which the customer purchased the commodity.

    Parts missing and defective upon receiving

    Time effectiveness: Declaration of parts missing and defective made within 7 days from the date of receipt is valid is valid. Please timely check the commodity after the receipt thereof.

    Procedure:

    1). Please send an email with subject indicating "Parts missing(or defective)" to tec-support@makeblock.cc. At the same time, the mail shall specify:

    a. Where the good was purchased (makeblcok official website / Amazon outlets / Taobao outlets / Jingdong outlets);

    b. Order No.;

    c. Tracking No.;

    d. Specific description on the missing or defective parts and quantity thereof. (Note: for names of the parts, please refer to the Parts List); e. return address (PO box and mail addresses are not available;the ZIP code is required), contact person and contact number.

    2). Within 2 working days after receiving the e-mail, Makeblock will verify and give a proposal for solving problem.

Reviews about mDrawbot Kit (Standard Version)

Average rating: 3 reviews
Total reviews: 3